Crestron QMI-FTMC Przewodnik Instalacji Strona 22
- Strona / 48
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
FlipTop Media Center Crestron QM-FTMC
Installation
NOTE: To prevent overheating, do not operate this product in an area that exceeds
the environmental temperature range listed in the table of specifications.
Consideration must be given if installed in a closed or multi-unit rack assembly,
inside a closed desk or in a closed podium since the operating ambient temperature
of these environments may be greater than the room ambient temperature. Contact
with thermal insulating materials should be avoided on all sides of the unit.
NOTE: The following section does not apply to NB models. If you have an NB
model, please skip to “QM-FTCMK Cable Management Plate” on page 19.
Button Installation
The QM-FTMC is shipped with ten large blank buttons. You can order a variety of
button kits (sold separately) to add as many as 20 engraved or blank buttons.
Button Kits
KIT NUMBER DESCRIPTION
FT-BTNB-L One large button engraved as desired
FT-BTNB-L-BLANK One large button not engraved
FT-BTNB-S Two small buttons with divider engraved as desired
FT-BTNB-S-BLANK Two small buttons with divider, not engraved
To replace the large buttons with small buttons, follow this procedure.
A 1/16" Allen (hexhead) wrench is required to remove the button faceplate.
1. Remove the four Allen screws that secure the button faceplate.
2. While holding adjacent buttons in place, carefully pull the button(s) to be
replaced from the rubber membrane.
3. Carefully press the two small replacement buttons in place, making sure
LED window faces up. Use care not to dislodge the membrane and circuit
board.
NOTE: The removable buttons fit snugly on the rubber membrane. Remove
carefully to avoid pulling the membrane from the unit.
4. The divider bar slips into the slots on the back of the faceplate.
5. Replace the faceplate.
18 • FlipTop Data Center: QM-FTMC Operations & Installation Guide – DOC. 6311B
- Crestron QM-FTMC 1
- Contents 3
- QuickMedia™ FlipTop Media 5
- Center: QM-FTMC 5
- FlipTop Housing 6
- Multimedia Interface 6
- Integrated Keypad (optional) 6
- AV Switcher and Mic Preamp 6
- QuickMedia™ Transport 6
- Internal Block Diagram 8
- Specifications 9
- Physical Description 11
- 13.24 cm 12
- 15.87 cm 12
- 13 14 15 16 17 14
- 1 Ground 15
- 2 Ground 15
- 3 Luminance 15
- 4 Chrominance 15
- PIN SIGNALS 16
- Industry Compliance 19
- Network Wiring 20
- QuickMedia Wiring 20
- CresCAT-QM 20
- QM Network Topology 21
- Installation 22
- • Phillips screwdriver 23
- Mounting to Surface 25
- Ground Wire Connections 28
- Configuration Software 29
- C2Net Device, Slot 9 30
- 11 12 13 14 15 31
- 16 17 18 19 20 31
- Example Program 32
- Setting Microphone Gain 33
- Setting the Gating Level 34
- Uploading and Upgrading 35
- Program Checks 36
- Problem Solving 37
- Functions 38
- Reference Documents 39
- Further Inquiries 39
- Future Updates 40
- DESCRIPTION COUNTRIES 41
- Installation Notes 42
- Compensation 42
- Switchers 43
- QM-AE Audio Extractor 43
- CRESTRON Limited Warranty 46
- Tel: 888.CRESTRON 03.07 48
Powiązane produkty i podręczniki dla Klawiatury numeryczne Crestron QMI-FTMC
Klawiatury numeryczne Crestron CNX-BF12 Dokumentacja
(100 strony)
(100 strony)
Krystal Touch of NY DL3660CPRI manuals
Owner’s manuals and user’s guides for Unknown Krystal Touch of NY DL3660CPRI.
We providing 1 pdf manuals Krystal Touch of NY DL3660CPRI for download free by document types: Installation Guide
Komentarze do niniejszej Instrukcji