Crestron ST-LT Dokumentacja

CRESTRON 4. Notice the list of current network devices in the dialog box. Highlight the ST-LT. 5. The factory set NET ID of the ST-LT (1C) appears

CRESTRON Changing the NET ID - ST-LT Workshop Screens (2 of 3) 5. Enter a new NET ID code (in two-digit hexadecimal format) and depress ENTER. The

CRESTRON 4. Slide the top cover toward the back panel while holding the ST-LT in place until the cover is free. 5. Locate the dip switch and noti

CRESTRON Preparation for Use Refer to the two hookup diagrams below. The first diagram illustrates the connections to SmarTouch STS. The second diag

CRESTRON Programming Using STS/VTW Software NOTE: The following description assumes that the reader has some knowledge of STS/VTW software. If not,

CRESTRON Select Open and Project from the File menu to open the touchpanel project file. For this sample, the project has been named LUTRON.PRJ. Th

CRESTRON The macro in this sample shall address MAIN-UNIT-2 and select ZONE-1-UP. 8. A macro is created by adding the appropriate commands and del

CRESTRON SIMPL SIMPL is CRESTRON’s programming language designed for easy implementation of the control system requirements. The best representation

CRESTRON ST-LT Workshop Screens (2 of 4) ST-LT Workshop Screens (3 of 4) ST-LT Workshop Screens (4 of 4) The ST-LT is defined as an “ST-COM, Port

CRESTRON The data field contains the command protocol for the Grafik Eye system. A description of commands, their operation, and examples are provid

CRESTRON Problem Solving Troubleshooting The table below provides corrective action for possible trouble situations. If further assistance is requir

CRESTRON Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange, or service witho

CRESTRON Appendix: GRAFIK Eye Commands NOTE: This entire appendix is a reprint of Lutron’s technical reference material. Format for Commands The RS

CRESTRON Examples: :A21<CR>Select scene 2 on GRAFIK Eye Main Unit 1.:AG45 A78<CR>Select scene 16 on GRAFIK Eye Main Units 4 and 5; selec

CRESTRON Example of Response: <CR><LF>~:ss2L0MAR95 1 OK<CR><LF> Main Unit A1 is in scene 2

CRESTRON (D) Zone Lower This command causes the zones of the selected GRAFIK Eye Main Units to gradually decrease in intensity. The first parameter

CRESTRON Examples: :C<CR>Stop all zones on all GRAFIK Eye Main Units that are ramping up. :C E<CR>Stop all zones that are being raised o

CRESTRON 0 = no schedule active1 = "weekday" schedule2 = "weekend" schedule3 = "special 1" schedule4 = "special 2

CRESTRON Example: :QS<CR>Start super sequence. (QP) Super Sequence Pause This command stops the preprogrammed super sequence that is running a

CRESTRON This page intentionally left blank. Operations Guide - Doc. 5694 Lutron Interface

CRESTRON Contents Lutron Interface 1 Description...

CRESTRON This page intentionally left blank. 26 • Lutron Interface Operations Guide - Doc

CRESTRON Operations Guide - Doc. 5694 Lutron Interface • 27 This page intentionally left blank.

CRESTRON Lutron Interface Description Functional Description There are two CRESTRON Lutron Interface configurations available: ST-LT and STI-LT. Con

CRESTRON ST-LT Physical Views ST-LT Ports A number of ports are provided on the back of the ST-LT. Each has a silk-screened label. Refer to illustr

CRESTRON NET These two 6-pin, 6-position RJ11 modular jacks are used to connect the ST-LT module to either the SmarTouch STS or CRESNET II remote co

CRESTRON ST-LT Indicators There are seven LED indicators located on the front panel of the ST-LT. Refer to illustration and descriptions below. ST-

CRESTRON Leading Specifications The table below provides a summary of leading specifications for the ST-LT module. Dimensions and weight are approxi