Crestron CP2 Dokumentacja Strona 27
- Strona / 40
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Crestron CP2/CP2E 2-Series Integrated Control Processor
some may be internal (e.g., for a modem). Consult the manufacturer’s
documentation for further information about the COM ports on your
PC.
3. Check the ERR LED indicator on the front panel of the CP2/CP2E. If
this LED is illuminated, unplug the unit and reapply power after a few
seconds. If the LED illuminates again, call Crestron customer service.
4. With a serial connection, reset the control system as follows:
a. Open Viewport and click Setup | Communications Settings to
display the “Port Settings” dialog box. Choose RS-232 as the
connection type.
b. Set the baud rate of the PC to 115200.
c. Set the baud rate of the CP2/CP2E control system to 115200, as
follows:
- Press and release the HWR button on the unit’s front panel.
- Press and hold the SWR button for approximately three to five
seconds. The Viewport console should display the following
message:
Viewport Message
- Release the SWR button.
d. If communication still cannot be established:
- Remove power from the control system.
- Press and hold the SWR button on the front panel of the
CP2/CP2E.
- Reapply power to the control system.
- The Viewport console should display the message shown
above.
- Release the SWR button.
e. Select Set Baud Rate on the Viewport Functions menu (or press
F8) and choose any baud rate from the drop-down list. This will
attempt to establish a connection at the indicated baud rate. If the
connection is successful, both the PC and the control system will
be set to the new baud rate.
f. Reinitialize the unit by recycling the power or pressing the HWR
button. If the connection is established, the Viewport console
should display some text and the <CP2> or <CP2E> prompt.
g. If communication still cannot be established, contact Crestron
Customer Support.
Operations Guide - DOC. 5980 2-Series Integrated Control Processor: CP2/CP2E• 23
- Contents 3
- 2-Series Integrated Control 5
- Processor: CP2/CP2E 5
- Specifications 6
- Physical Description 7
- Controls and Indicators 8
- PIN DIRECTION DESCRIPTION 9
- 1 2 3 4 5 6 7 8 G 10
- LAN Port Pinout 11
- Setup/Installation 13
- Bussing Strip Installation 14
- Network Wiring 15
- RESISTANCE (R) WIRE GAUGE 16
- Programming the CP2 and CP2E 17
- Slot 1: C2Net-Device 18
- Slot 2: C2I-IR8 18
- Slot 3: C2I-IO8 19
- About the IP Table 21
- Slot 6: C2I-COM3 22
- SIMPL+ Toolbar 23
- Module Header Information 24
- CP2/CP2E 25
- Viewport Message 27
- “Send Program” Dialog Box 28
- Advanced Console Commands 31
- Troubleshooting 32
- Passthrough Mode 33
- Passthrough Mode Dialog Box 34
- Further Inquiries 35
- Future Updates 35
- Software License Agreement 36
- PROPRIETARY RIGHTS 37
- GOVERNING LAW 37
- CRESTRON LIMITED WARRANTY 37
- Return and Warranty Policies 38
Powiązane produkty i podręczniki dla Networking Crestron CP2
(11 strony)Krystal Touch of NY DL3609BPRI manuals
Owner’s manuals and user’s guides for Unknown Krystal Touch of NY DL3609BPRI.
We providing 1 pdf manuals Krystal Touch of NY DL3609BPRI for download free by document types: Installation Guide
Komentarze do niniejszej Instrukcji